TDK 1.4 to 3W DC-DC converters operate from a 12V input and provide very low noise output voltages of up to 2,000V

May 26th, 2021
tdk-lambda-logo

TDK Corporation announces the introduction of the high voltage output CHVM series of DC-DC converters. Capable of operating from a nominal 12V input, these non-isolated converters deliver output voltages ranging from 180V to 2,000V. Low output ripple and noise is achieved through the use of a metallic case that provides five-sided shielding to reduce radiated emissions. The CHVM has been designed for use in noise sensitive applications, including photomultiplier tubes, photodiodes, scanning electron microscopes, X-ray fluorescence spectrometers, mass spectrometers and ultrasonic probes.

Learn more at us.lambda.tdk.com

Tags: ,
Posted in Showcase | No Comments »

Simplify Daisy-Chaining with Mill-Max Spring-Loaded Pins

May 26th, 2021
mill-max-logo

Mill-Max has developed a versatile line of horizontal surface-mount (HSMT) spring-loaded pins designed for making low profile connections parallel to the board surface. These spring-loaded pins have plunger travel in-line with the board surface, making them ideal for end-to-end board connections in assemblies with restrictive height requirements.

Learn more at mill-max.com

Tags: ,
Posted in Showcase | No Comments »

Spotlight: ITT Cannon’s New NetSplice Kit

May 14th, 2021

ITT Cannon’s new NetSplice kit offers easy-to-install splices for repairing cables on military and commercial aircraft systems. This innovative, lightweight and cost-effective solution uses standard wiring tools to splice together damaged cables used in data transfer and RF applications.

ITT-Cannon-NetSplice-Sell-SheetDownload

Tags:
Posted in Showcase | No Comments »

TDK Corporation Introduces the 750W Rated i7A Non-Isolated DC-DC Converters

May 14th, 2021
tdk-lambda-logo

Capable of operating from an input voltage of 18V to 32V, the step-down converters deliver an output voltage that can be adjusted from 3.3 to 18V with an output current of up to 45A. The series has been optimized for a 24V nominal input and weighing just 25g, is intended for use in a wide range of applications including robotics, drones, medical, communications, industrial, test, measurement and battery powered equipment.

Learn more at us.lambda.tdk.com

Tags: ,
Posted in Showcase | No Comments »

Mill-Max Introduces A New Series of Open Receptacles Designed to Make Mechanical Key Switches Hot-Swappable

May 14th, 2021
mill-max-logo

Mill-Max has recently developed a new series of open bottom, low profile, solder mount receptacles specifically designed to make your mechanical key switches hot-swappable. The new 3305-X  is designed to be soldered into a .060” (1,50mm) minimum mounting hole, with an ultra-thin retention shoulder so plugged-in components sit nearly flush to the board surface. The open bottom design is meant to accommodate varying lead lengths making this a very versatile receptacle.

Learn more at mill-max.com

Tags: ,
Posted in Showcase | No Comments »

C&K Launches Low-Profile Tactile Switch For Wearable Devices

May 3rd, 2021

C&K, has developed a miniature SMT tactile switch designed for wearable and portable IoT devices. The PTS847 Series side-actuated tact switch combines a space-saving design with heightened durability to handle drop-impacts common to consumer devices.

At only 4.6 mm x 2.2 mm x 2.6 mm, the PTS847 Series features an edge mount configuration that raises a mere 0.95 mm above the PCB for valuable PCB saving and customer system space saving. Supporting 200K cycles, the low profile SMT switches are commonly used in wearable and IoT devices including sport watches, hearing aids, health monitoring devices, Bluetooth accessories and more

Learn more at ckswitches.com

Tags: , , ,
Posted in Showcase | No Comments »